환영 Recepción Willkommen
Bienvenue
Welcome 欢迎 歓迎
|
We can disassemble, package, transport heavy equipment and put them all
back for you.
Before the disassembly of the Wirebonder:
|
|
|
|
View from the right |
|
|
|
Front view |
|
|
|
IO module attached to the left |
|
|
|
|
View from the left |
|
|
|
|
|
|
|
Modules are bolted together at lower beam area |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
one Monitor was not used |
|
|
|
|
|
|
|
|
The tall pipe
|
|
|
|
Head area |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Grounding Wires are yellow/green
|
|
|
|
|
|
|
|
|
|
|
Release the strap |
|
|
|
Control Panel wiring |
|
|
|
Panel wiring |
|
|
|
panel wiring |
|
|
|
|
|
panel wiring |
|
|
|
panel wiring |
|
|
|
panel wiring |
|
|
|
panel wiring |
|
|
|
where the wire goes |
|
|
|
|
|
Connectors have labels, match the labels to reconnect
match connector's labels |
|
|
|
Wiring inside the Control Panel
Match the label #'s to reconnect wires |
|
|
|
|
remove all the straps, except the control panel's strap, need this one to hold it up |
|
|
|
|
|
|
Servo motor is under the IO module, not to damage it with Forklift |
|
|
|
Control Panel rotated
keep a strap around the heavy control panel first, remove 3 bolts, then rotate the panel to the original location |
|
|
|
Outer control panel to be attached with hinges |
|
|
|
Many cables have to be reconnected from the bottom slots |
|
|
|
|
|
|
|
|
|
|
Lift the module and insert rollers
|
|
|
|
|
|
Wires at bottom
The bottom wire protector may be out of place |
|
|
|
|
|
|
Cut the pipe off
|
|
|
|
|
|
|
The wirebonder was disassembled in two modules. The control panel is
rotated 90 degrees,
and the pipe at top is cut to fit into a 20' L X 92.6" W X 92" H container.
Before the disassembly of Laser Solder:
|
|
|
|
|
Laser right module
|
|
|
|
Laser Front view |
|
|
|
Lasetr main control area |
|
|
|
|
|
|
Top of laser
There are many cables and connectors need to be reconnected on the top. Use a ladder to climb up. |
|
|
|
|
|
cooler unit
Not all the coolers are used, blue barrel has the cooler liquid, not sent. |
|
|
|
another cooler
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Cooler |
|
|
|
|
|
Rear view |
|
|
|
|
|
Rear view
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
network box on the top
|
|
|
Laser was disassembled into three modules, and loaded into a 8.5' tall container:
Flipchip
|
|
|
|
Flipchip front view
items on the floor are for somethings else |
|
|
|
|
|
|
View from the right
|
|
|
|
|
|
View from the right
Manuals are in the boxes |
|
|
|
Rear view
|
|
|
|
View from the left
|
|
|
|
Utility support frame
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
These are not flipchip's |
|
|
|
|
|
|
Yellow/green wire is ground
|
|
|
|
|
|
cables have ID stickers
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
air line
Pull the blue connector back to disconnect the air line |
|
|
|
|
|
|
|
|
|
Beam end view
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
reinsert the slider
|
|
|
|
|
|
Beam slider
Very fragile part |
|
|
Pick and Place
|
|
|
|
View from the right
|
|
|
|
View from right front
|
|
|
|
|
Front control area
|
|
|
|
Rear view
|
|
|
|
|
|
Connected to Printer
|
|
|
|
Parts Bin
No feeders are availble |
|
|
|
|
Top of Pick and Place
Only a few cables need to be reconnected from the top |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Head glider
Do not loosen the roller balls on the sliding rails |
|
|
|
Beam
Beam has a slider, do not loosen the rolling balls |
|
|
|
|
|
Wiring inside the beams
each black cable inside the beam was cut near the source end. Need to resolder them back. |
|
|
|
|
|
|
|
|
Control station
|
|
|
|
|
|
|
|
|
Head-holding Beams removed
|
|
|
|
|
PP Heads removed
|
|
|
Printer
|
|
|
|
Printer front view
Printer and Pick and place are on opposite side but are connected |
|
|
|
|
Printer table
|
|
|
|
|
printer table
remove the angles steel feet from the table, and then attached the table to the printer |
|
|
|
|
|
|
|
|
|
Top
Not many cables up there |
|
|
|
|
|
|
|
|
Printer has no working head
Head was removed by the the original owner |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
More...
Digital Computing System
